Bissell 7700 E Manual

							11www.bissell.com
Operation
Carpet Cleaning (continued)
7.  Continue to clean entire carpet working in 
one meter by one meter sections.
8.  If machine loses suction, stop spraying and 
check the collection tank level. Empty if 
necessary.
9.  If the machine stops spraying turn off 
wet clean button immediately and check the 
solution tank level. 
NOTE: Never run in wet clean mode when 
the clean water formula tank is dry or 
missing.
When you are finished
1.  Turn off the heater, wet clean, 
and power buttons.
2.  Remove the collection tank from the unit by 
opening the quick release hose holder and 
lifting the tank straight up by the handle.
3.  Remove the top lid from the collection tank 
and set it aside.
4.  Empty dirty water into a sink, toilet or outside. 
Pour the dirty water out from the corner of the 
tank. Rinse out the tank thoroughly.
NOTE: You may leave the solution tank with 
water and formula in it so you are ready for 
the next use.
6.  Allow all parts to dry before storing.
Hard floor cleaning
1.  See “Getting Ready to Wet Clean” on Page 10.
2.  Be sure to use BISSELL Hard Floor Solutions 
in the solution tank for hard floor cleaning. 
Fill the formula tank by first unscrewing the 
measuring cap. Always use genuine BISSELL 
formulas to maximize cleaning and for the 
safety of your machine. Fill tank to fill line 
with hot tap water. Add one full cap of formula. 
Screw measuring cap tightly back onto the 
solution tank.
3.  Set the solution tank back in the machine.
23
2
ug120-4005_7700_607.indd   11ug120-4005_7700_607.indd   116/28/07   10:05:56 AM6/28/07   10:05:56 AM 
						

							12www.bissell.com
Operation
Hard floor cleaning (continued)
4.  Attach microfibre pad to quick dry hard floor tool by 
attaching to the Velcro strips on the top of the tool.
5.  Attach the quick dry hard floor tool to end of 
the wand.
6.  Place tool directly on the hard floor surface, 
resting on the pad.
7.  Squeeze the spray trigger to moisten the pad 
with cleaning solution. 
Caution: Do not oversaturate.
8.  Move the tool back and forth across the floor 
to clean. Squeeze spray trigger as needed.
9.  Tilt the tool forward and pull back. This will 
create the best suction and will help get the 
hard floor surface as dry as possible.
10.  Continue until room is complete.  
11.  See “When You Are Finished” instructions on 
page 11.
12.  Be sure to remove the microfibre pad and 
clean it by hand or machine wash as needed. 
Allow it to dry completely before next use.
Upholstery cleaning
Your PROheat All-Rounder comes with special 
tools for vacuuming and wet cleaning upholstery, 
stairs and more.
1. Important! If using to wet clean upholstery, 
check the upholstery tags proceeding.
a.  Check manufacturer’s tag before 
cleaning. “W” or “WS” on the tag means 
you can use your PROheat All-Rounder.  
If the tag is coded with an “X” or an “S” 
(with a diagonal stripe through it), or 
says “Dry Clean Only”, do not proceed 
with deep cleaning. Do not use on velvet 
or silk.  If manufacturer’s tag is missing 
or not coded, check with the furniture 
maker or the furniture dealer.
b.  Check for colourfastness in an 
inconspicuous place.
c.  If possible, check upholstery stuffing. 
Coloured stuffing may bleed through 
fabric when wet.
d.  Plan activities to allow upholstery time 
to dry.
e.  Vacuum thoroughly.  2
Adsdfdd ghg bvh
cvbbj jkn hnbj jkvh
gcghhjj  jhffhl kllgh
Manufacturer’s tag
ug120-4005_7700_607.indd   12ug120-4005_7700_607.indd   126/28/07   10:05:59 AM6/28/07   10:05:59 AM 
						

							13www.bissell.com
Operation
Upholstery cleaning (continued)
2.  Refer to the “Getting Ready to Wet Clean” on 
page 10.
3.  Attach the desired wet cleaning tool to the 
wand or grip.
4.  Clean by pressing the spray trigger to spray 
solution onto the area to be cleaned. Slowly 
move the tool back and forth over the soiled 
surface.  Release the spray trigger to suction 
soiled water.  Continue to clean the area, 
working in small sections, until no more 
dirt can be removed. Suction as needed to 
remove as much water as possible. 
Caution: Do not overwet.
5.  Remove and rinse tools in clean, running 
water. Dry and put away.
6.  See When you are finished instructions on 
page 11.
Cleaning fluid section
Keep plenty of genuine BISSELL Formula on 
hand so you can clean and protect whenever it 
fits your schedule. Always use genuine BISSELL 
deep cleaning formulas. 
1.42 L 
Fiber Cleansing 
Formula
™ 
with 
Scotchgard™ 
protector
item # 710E
1.42 L
Multi-Allergen 
Removal
™ Formula 
with Scotchgard™ 
protector
item # 720E
1.42 L
Pet Odor and Soil 
Removal
™ Formula 
with Scotchgard™ 
protector
item # 730E
1.42 L
Natural Orange 
Extract Formula
™ 
with Scotchgard™ 
protector
item # 740E
1.42 L
Lavender Essence 
Formula
™ 
with 
Scotchgard™ 
protector
item # 750E
1.42 L
Lavender Essence 
Formula
™ 
with 
Scotchgard™ 
protector
item # 750E
Tip:
It is recommended that you 
suction clean water from the 
tap to rinse out the hose.
ug120-4005_7700_607.indd   13ug120-4005_7700_607.indd   136/28/07   10:06:00 AM6/28/07   10:06:00 AM 
						

							Maintenance and care 
Machine storage
Once your cleaning is complete make sure the dirty 
water from the collection tank is emptied. Rinsed out 
and dry before the next use. For wet cleaning, the solu-
tion tank can be left filled and ready to use.  
Note: Store your PROheat All-Rounder in a 
protected dry area. Since this product uses 
water it must not be stored where there is a 
danger of freezing. Freezing will damage the 
internal components and void the warranty.
 WARNING: To reduce the risk of 
fire and electric 
shock due to internal 
component damage, 
use only BISSELL Deep 
Cleaning Formula 
intended for use with 
the deep cleaner.  
Non-BISSELL cleaning 
formula may harm the 
machine and void the 
warranty.
14www.bissell.com
ug120-4005_7700_607.indd   14ug120-4005_7700_607.indd   146/28/07   10:06:09 AM6/28/07   10:06:09 AM 
						

							Maintenance and care 
Machine care
For best results, a few simple steps can assure 
your machine is well maintained after your 
cleaning is complete.
1.  Press all buttons OFF. Unplug the machine 
and wrap the cord.
2.  After emptying the dirty water from the 
collection tank, rinse it out thoroughly with 
hot water. Remove all inner parts (water 
filtration tower and mode selector) if desired. 
Rinse them and allow to dry before returning 
into tank.
Note: To remove inner parts, turn mode 
selector to remove. Pull mode selector straight 
out towards you. The water filtration tower can 
now be taken out through the top of the tank.
3.  For wet cleaning, remove and clean all tools 
that were used. Allow to dry before storing.
4.  Remove the hose, taking care to keep both 
ends up to avoid spilling. Dump out any 
remaining water and flush clean with hot tap 
water. Allow to dry before storing.
5. a. Pre-motor filter: Take apart the top lid by 
pulling the tab away from the separator. 
Inspect the foam filter. If dirty, rinse clean 
and allow to dry before returning it to the 
machine. Re-assemble the top lid by plac-
ing the filter in its spot and re-attaching 
the separator. Use care to make sure the 
“T” pieces are lined up under the shallow 
grooves on the top lid itself. For replace-
ment of this part, see pages 18-19.
  b.  HEPA Media filter: This filter is located at 
the back of the machine, underneath the 
Quick Release Cord Wrap. Use one finger to 
depress the latch and pull the door down. 
Open towards you and down to the ground. 
Use two hands to remove the filter from 
its slot. If dirty, rinse clean and allow to dry 
before returning it to the machine. Make 
sure the filter door is fully closed prior to 
operating the machine. For replacement of 
this filter see pages 18-19.
www.bissell.com15
Water Filtration 
TowerMode Selector
ug120-4005_7700_607.indd   15ug120-4005_7700_607.indd   156/28/07   10:06:09 AM6/28/07   10:06:09 AM 
						

							Troubleshooting 
Reduce Spray or No Spray
Possible Cause  Remedies
1.  Make sure power is on 1.  Press power button if needed
2.  Solution tank may be empty 2.  Fill tank according to directions  
3.  Tank may not be seated properly 3. Turn ON/OFF, heater and wet clean 
      button off. Remove and reseat tank
4.  Hose solution line may be disconnected 4.  Check connection at front of 
    machine
5.  Wet clean is not turned on 5.  Depress wet clean button to turn on
Machine is not suctioning
Possible Cause  Remedies
1.  Collection tank may not be placed properly 1.  Open Quick Release™ Hose Door, lift 
      out tank and re-seat. Re-latch Quick 
      Release™ Hose Door 
2.  Collection tank may not be  2.  Check to make sure the top lid is 
 assembled properly   properly seated
3. Wand tool connections are not tight 3. Check all connections 
      (At grip, wand and tool) 
      Push tight if necessary.
4. Collection tank is full 4. Empty collection tank by following 
      instruction on page 9
5. Float has tripped 5. Check to see if tank needs to be 
      emptied. Make sure float is down 
      towards bottom of tank.
6. Pre-motor filter is dirty 6. Remove top lid. Remove and 
      clean pre-moter filter by following 
      instructions on page 15. 
      Filter must be completely dry 
      before using again
Built-in heater light does not illuminate
Possible Cause  Remedies
1.  The heater button has not been depressed 1.  Depress the heater button
2.  The ON/OFF button has not been depressed 2. Depress the ON/OFF button
Other maintenance or service not included in the manual should be performed by an 
authorized service representative.
Thank you for selecting a BISSELL product.
Please  do  not  return  this  product  to  the  store.             
 WARNING: To reduce the risk of fire, 
electric shock or injury 
unplug from outlet before 
servicing.
16www.bissell.com
ug120-4005_7700_607.indd   16ug120-4005_7700_607.indd   166/28/07   10:06:12 AM6/28/07   10:06:12 AM 
						

							www.bissell.com
BISSELL Consumer Services
If your BISSELL product should require service:
 In the UK, or New Zealand, call BISSELL Consumer Services at the numbers below and we will give 
you the location of a BISSELL Authorized Service Center in your area. For all other countries, contact your local 
in country distributor for questions, service, or repair. 
If you have questions about your warranty or need replacement parts please contact the numbers below.
Or visit the BISSELL website - www.bissell.com
When contacting BISSELL, have model number of unit available.
Please record your Model Number: ___________________
Please record your Purchase Date: ___________________
Note: Please keep your original sales receipt. It provides proof of date of purchase in the event of a 
warranty claim. See Warranty on page 20 for details.
Please do not return this product to the store.
17
For UK inquiries:
Monday - Thursday  9 am — 5 pm 
  Friday  9 am — 4 pm 
BISSELL Homecare (Overseas) Inc.
The Boat Yard 
105 Straight Road 
Old Windsor 
Berkshire, SL4 2SE
United Kingdom 
Telephone: 0870-225-0109 
For all other inquiries:
Monday - Friday    8 am — 4 pm 
BISSELL Homecare, Inc.
PO Box 1888
Grand Rapids, MI 49501 USA
Telephone: 01-616-453-4451 
Fax: 01-616-453-1383For New Zealand inquiries:
Monday - Friday    9 am — 5 pm 
Parex Industries Ltd.
103 Central Park Drive
Henderson
Auckland
New Zealand
Telephone: 0800-247-735 
ug120-4005_7700_607.indd   17ug120-4005_7700_607.indd   176/28/07   10:06:13 AM6/28/07   10:06:13 AM 
						

							www.bissell.com
Replacement parts - BISSELL PROheat All-Rounder
Below a list of common replacement parts*. While not all of these parts may have come 
with your specific machine, all are available to you for purchase, if desired.
Item Part No.  Part Name
 1  203-7063  Mulit-Surface Floor Tool 
 2  203-7064  Air Powered Floor TurboBrush
 3  203-7073  5 Brush
 4  203-7066  Wand 
 5  203-7067  Adaptor
 6  203-7068  Crevice Tool
 7  203-7069  Upholstery Dusting Brush
 8  203-7070  Carpet Deep Cleaning Tool
 9  203-7071  Carpet Deep Cleaning Tool Brush Strip
10 203-7072 Carpet Deep Cleaning Tool Adaptor
11 203-7065 4 Upholstery Tool
12 203-7074 Quick Dry Hard Floor Tool (pads not included)
13 203-7076 Hard Floor Microfibre Pads (2 Pack)
14 203-7077 Drain Cleaner
15 203-7078 Tool Caddy
16 203-7079 Hose Grip Assembly
17 203-7080 Measuring Cap
18 203-7082 Pre-Motor Filter
19 203-7083 HEPA Media Filter
20 203-7084 Solution Tank
21 203-7085 Small cap/insert
22 203-7086 HEPA Filter Door
23 203-7087 Float
24 203-7088 Diverter
25 203-7089 Water Filtration Tower
26 203-7090 Water Filtration Tower Gasket
27 203-7091 Separator with Filter
28 203-7092 Top Lid Assembly 
29 203-7093 Lid
30 203-7096 Collection Tank 
31 203-7097 Collection Tank Assembly
32 203-7098 Motor Duct Gasket
33 203-7099 Quick Release™ Hose Door™ Assembly
34 203-7100 Carry Handle Assembly
35 203-7102 Caster Wheel
36 710E 1.42 L Fiber Cleansing Formula
™ with Scotchgard™
 protector
37  720E  1.42 L Multi-Allergen Removal™ Formula with Scotchgard™
 protector
38  730E  1.42 L Pet Odor and Soil Removal™ Formula with Scotchgard™ protector
39 740E 1.42 L Natural Orange Extract Formula™ with Scotchgard™ Protector
40 750E 1.42 L Lavender Essence Formula™ with Scotchgard™ protector
41  0484  0.95 L Hard Floor Solutions™
*Not all parts are included with every model.
18
ug120-4005_7700_607.indd   18ug120-4005_7700_607.indd   186/28/07   10:06:13 AM6/28/07   10:06:13 AM 
						

							Replacement parts - BISSELL PROheat All-Rounder
 1 2 3 4 5 6 7
 8 91011121314
15161718192021
22232425262728
29303132333435
36 37 38 39 40 41   
       
19www.bissell.com
(Pads not included
ug120-4005_7700_607.indd   19ug120-4005_7700_607.indd   196/28/07   10:06:13 AM6/28/07   10:06:13 AM 
						

							20www.bissell.com
Warranty - BISSELL PROheat All-Rounder
 This warranty gives you specific legal rights, and you may also have other rights which may vary from country 
to country. If you need additional instruction regarding this warranty or have questions regarding what it may 
cover, please contact BISSELL Consumer Services by telephone, or regular post as described below, or 
contact your local in country distributor.
 Limited Two Year Warranty
 Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, BISSELL Homecare, Inc., will replace (with 
new or remanufactured components), at BISSELL’s option, free of charge from the date of purchase by the 
original purchaser, for two years any defective or malfunctioning part do to manufacturers defect. 
 This warranty applies to product used for personal, and not commercial or rental service. This warranty does 
not apply to fans or routine maintenance components such as filters, belts, or brushes. Damage or malfunction 
caused by negligence, abuse, or use not in accordance with the User’s Guide is not covered.
BISSELL HOMECARE INC. IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL 
DAMAGES OF ANY NATURE ASSOCIATED WITH THE USE OF THIS PRODUCT. 
BISSELL’S LIABILITY WILL NOT EXCEED THE PURCHASE PRICE OF THE PRODUCT. 
*EXCEPTIONS AND EXCLUSIONS FROM THE TERMS OF THE LIMITED WARRANTY
THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES 
EITHER ORAL OR WRITTEN. ANY IMPLIED WARRANTIES WHICH MAY ARISE 
BY OPERATION OF LAW, INCLUDING THE IMPLIED WARRANTIES OF 
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED 
TO THE TWO YEAR DURATION FROM THE DATE OF PURCHASE AS 
DESCRIBED ABOVE.
For UK inquiries:
Monday - Thursday  9 am — 5 pm 
  Friday  9 am — 4 pm 
BISSELL Homecare (Overseas) Inc.
The Boat Yard 
105 Straight Road 
Old Windsor 
Berkshire, SL4 2SE
United Kingdom 
Telephone: 0870-225-0109 
For all other inquiries:
Monday - Friday    8 am — 4 pm 
BISSELL Homecare, Inc.
PO Box 1888
Grand Rapids, MI 49501 USA
Telephone: 01-616-453-4451 
Fax: 01-616-453-1383For New Zealand inquiries:
Monday - Friday    9 am — 5 pm 
Parex Industries Ltd.
103 Central Park Drive
Henderson
Auckland
New Zealand
Telephone: 0800-247-735 
©2007 BISSELL Homecare, Inc
Grand Rapids, Michigan
All rights reserved. Printed in China
Part Number 120-4005
Rev 6/07
Visit our website at:
www.bissell.com
Scotchgard is a trademark of 3M
ug120-4005_7700_607.indd   20ug120-4005_7700_607.indd   206/28/07   10:06:32 AM6/28/07   10:06:32 AM