AT&T Htc Tilt 2 User Manual

							
Managing Your Device   51

Performing a hard resetIf a normal reset does not solve a system problem, you can perform a hard (full) reset. After a hard reset, the device is restored to its default settings—the way it was when you first purchased it and turned it on. You will lose any programs you installed, data you entered, and settings you customized on your device, and only Windows Mobile® software and other pre-installed programs will remain.
Warning!    Your device will be set back to factory default settings. Make sure that any additional installed programs and/or user data have been backed up before you perform a hard reset.
Important If Encrypt files when placed on a storage card is enabled, backup all files from the storage card before using Clear Storage, hard reset, or updating the operating system. Otherwise you will no longer be able to access the encrypted files on the storage card. Use ActiveSync or Windows Mobile Device Center to transfer files between your storage card and computer. After the procedure, copy your files back to the storage card.
To perform a hard reset1. With the device turned off, press and hold the TALK/SEND, END and POWER buttons until you see this message on the screen.
This operation will delete all your personal data, and reset all settings to manufacturer default. Press VolUp to restore manufacturer default, or press other keys to cancel.
2. Release the TALK/SEND, END and POWER buttons.
3. Press the VOLUME UP button to perform the hard reset, or press any other button to cancel the reset. 
						

							
5  Managing Your Device

Using Clear StorageIf you can access the device settings, you can use Clear Storage to reset your device back to factory default settings.
1. Tap Start > Settings > System > Clear Storage.
2. Enter “1234” and then tap Yes. 
						

							
Managing Your Device   5

13.8 Connecting to an External Display
Your device has a TV output which can be connected to an external display, such as a TV monitor, that has an RCA cable socket. This allows you to output the device screen and audio to a big-screen display.
Note  You need an HTC TV Out cable to be able to connect your device to an external display. The HTC TV Out cable is sold separately.
To connect the device to an external display1. Turn off the external display.
2. Connect the ends (red, white, and yellow RCA plugs) of the HTC TV Out cable to the external display’s RCA sockets. 
3. Connect the mini-USB end of the HTC TV Out cable to the sync connector at the bottom of the device. The TV Out screen opens.
4. Choose the video standard to use when outputting the video and then tap Done.
For example, if your video is in the NTSC standard and you select PAL-M, TV Out will automatically convert your video to PAL-M before it outputs to the external display.
Note If you need to change the video standard option in the future, tap Start > Settings > All Settings > System tab > TV Out. 
5. Tap the type of media you want to output. 
6. Turn on the external display and then switch it to the input signal that you connected the HTC TV Out cable to (for example, Video 1). 
The screen orientation is always in landscape mode while your device is connected to the external display. 
						

							
54  Managing Your Device
This Page Intentionally Left Blank 
						

							
A.1  Specifications
Processor Qualcomm® MSM701A™, 58 MHz
Operating SystemWindows Mobile® 6.5 Professional
MemoryROM: 51 MBRAM: 88 MB
Dimensions (LxWxT )116 X 59.5 X 16.55 mm (4.57 X .4 X 0.65 inches)
Weight178.5 grams (6. ounces) with battery
Display.6-inch TFT-LCD touch-sensitive screen with 480 x 800 WVGA resolutionAdjustable tilt screen
•
•
NetworkHSDPA/WCDMA850/1900/100 MHzUp to 84 kbps up-link and 7. Mbps down-link speeds
Quad-band GSM/GPRS/EDGE850/900/1800/1900 MHz
(Band frequency, HSDPA availability, and data speed are operator dependent.)
••
•
Device ControlTouchFLO™ DZoom bar••
KeyboardSlide-out 5-row QWERTY keyboard
GPSInternal GPS antenna
Appendix  
						

							
56  Appendix

ConnectivityBluetooth® .1 with Enhanced Data Rate and ADP for wireless stereo headsetsWi-Fi® (IEEE 80.11b/g)HTC ExtUSB™ (11-pin mini-USB .0, audio jack, and TV Out* in one)
•
••
Camera. megapixel color camera with auto focus
Audio supported formatsAAC, AAC+, eAAC+, AMR-NB, AMR-WB, QCP, MP, WMA, WAV, MIDI, M4A
Video supported formatsWMV, ASF, MP4, GP, G, M4V, AVI
BatteryRechargeable Lithium-ion batteryCapacity: 1500 mAh••
Talk time:  Up to 90 minutes for WCDMA  Up to 510 minutes for GSMStandby time: Up to 750 hours for WCDMA  Up to 500 hours for GSM
(The above are subject to network and phone usage.)
•
•
Expansion SlotmicroSD™ memory card (SD .0 compatible)
AC AdapterVoltage range/frequency: 100 - 40V AC, 50/60 HzDC output: 5V and 1A
Special FeaturesG-SensorStraight Talk™Noise-cancelling dual microphones and speakers
•••
* HTC TV Out cable needed.
Note Specifications are subject to change without prior notice. 
						

							
Appendix   57

A.2  Regulatory Notices
Regulatory Agency IdentificationsFor regulatory identification purposes, your product is assigned a model number of RHOD300.FCC ID: NM8RHOD00.To ensure continued reliable and safe operation of your device, use only the accessories listed below with your RHOD300.
The Battery Pack has been assigned a model number of RHOD160.
Operating temperature range: °F to 104°F (0°C to 40°C).
Note This product is intended for use with a certified Class  Limited Power Source, rated 5 Volts DC, maximum 1 Amp power supply unit.
Federal Communications Commission Notice This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and () this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harm-ful interference to radio or TV reception, which can be determined by turning the equipment on and off, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna. 
•  Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 
						

							
58  Appendix

•  Consult the dealer or an experienced radio or television technician for help. 
ModificationsThe FCC requires the user to be notified that any changes or modifications made to the device that are not expressly approved by HTC Corporation may void the user’s authority to operate the equipment.
FCC Hearing-Aid Compatibility (HAC) Regulations for Wireless 
DevicesOn July 10, 00, the U.S. Federal Communications Commission (FCC) Report and Order in WT Docket 01-09 modified the exception of wireless phones under the Hearing Aid Compatibility Act of 1988 (HAC Act) to require digital wireless phones be compatible with hearing-aids. The intent of the HAC Act is to ensure reasonable access to telecommunications services for persons with hearing disabilities.
While some wireless phones are used near some hearing devices (hearing aids and cochlear implants), users may detect a buzzing, humming, or whining noise. Some hearing devices are more immune than others to this interference noise, and phones also vary in the amount of interference they generate.
The wireless telephone industry has developed a rating system for wireless phones, to assist hearing device users find phones that may be compatible with their hearing devices. Not all phones have been rated. Phones that are rated have the rating on their box or a label located on the box.
The ratings are not guarantees. Results will vary depending on the user’s hearing device and hearing loss. If your hearing device happens to be vulnerable to interference, you may not be able to use a rated phone successfully. Trying out the phone with your hearing device is the best way to evaluate it for your personal needs.
M-Ratings: Phones rated M or M4 meet FCC requirements and are likely to generate less interference to hearing devices than phones that are not labeled. M4 is the better/higher of the two ratings. RHOD00 is rated M. 
						

							
Appendix   59

Hearing devices may also be rated. Your hearing device manufacturer or hearing health professional may help you find this rating. Higher ratings mean that the hearing device is relatively immune to interference noise. The hearing aid and wireless phone rating values are then added together. A sum of 5 is considered acceptable for normal use. A sum of 6 is considered for better use. A sum of 8 is considered for best use.
In the above example, if a hearing aid meets the M level rating and the wireless phone meets the M level rating, the sum of the two values equal M5. This should provide the hearing aid user with “normal usage” while using their hearing aid with the particular wireless phone. “Normal usage” in this context is defined as a signal quality that is acceptable for normal operation.
The M mark is intended to be synonymous with the U mark. The T mark is intended to be synonymous with the UT mark. The M and T marks are recommended by the Alliance for Telecommunications Industries Solutions (ATIS). The U and UT marks are referenced in Section 0.19 of the FCC Rules. The HAC rating and measurement procedure are described in the American National Standards Institute (ANSI) C6.19 standard.
For information about hearing aids and digital wireless phones
FCC Hearing Aid Compatibility and Volume Control:
http://www.fcc.gov/cgb/dro/hearing.html
Gallaudet University, RERC:
http://tap.gallaudet.edu/DigWireless.KS/DigWireless.htm 
						

							
60  Appendix

Exposure to Radio Frequency (RF) SignalsYour device contains a radio transmitter and receiver. The radiated output power is far below the international radio frequency exposure limits. These limits are part of comprehensive guidelines and establish permitted levels of RF energy for the general population. The guidelines are based on the safety standards previously set by international standards bodies:
•  American National Standards Institute (ANSI) IEEE. C95.1-199
• National Council on Radiation Protection and Measurement (NCRP). Report 86. 1986
• International Commission on Non-Ionizing Radiation Protection (ICNIRP) 1996
• Ministry of Health (Canada), Safety Code 6. The standards include a substantial safety margin designed to assure the safety of all persons, regardless of age and health.
The exposure standard for wireless mobile phones employs a unit of measurement known as the Specific Absorption Rate, or SAR. The standard incorporates a substantial margin of safety to give additional protection for the public and to account for any variations in usage.
As with other mobile radio transmitting equipment, users are advised that for satisfactory operation of the equipment and for the safety of personnel, it is recommended that no part of the human body be allowed to come too close to the antenna during operation of the equipment.
Your device has an internal antenna. Use only the supplied integral antenna. Use of unauthorized or modified antennas may impair call quality and damage the phone, causing loss of performance and SAR levels exceeding the recommended limits as well as result in non-compliance with local regulatory requirements in your country.
To assure optimal phone performance and ensure human exposure to RF energy is within the guidelines set forth in the relevant standards; always use your device only in its normal-use position. Do not touch or hold the antenna area unnecessarily when placing or receiving a phone call. Contact with the antenna