Apple ibook g4 14 inch late 2004 User Manual
Here you can view all the pages of manual Apple ibook g4 14 inch late 2004 User Manual. The Apple manuals for Notebook are available online for free. You can easily download all the documents as PDF.
Page 41
iBook G4 (14-inch Late 2004) Take Apart - 40 How to Add Spiral Tubing to Protect the Inverter Ca- How to Add Spiral Tubing to Protect the Inverter Cable Important: The inverter cable can be pinched or damaged during reassembly of the bottom case. To protect the inverter cable, add spiral tubing to the cable, as shown in this procedure. Do not pull, twist, or strain the cable as you perform this procedure. Note: Images shown in this procedure may differ somewhat from the iBook model that you are...
Page 42
41 - iBook G4 (14-inch Late 2004) Take Apart How to Add Spiral Tubing to Protect the Inverter Ca- 3. Release the cable from the channel in the frame. 4. Holding the cable steady, wrap the spiral tubing around the cable at the clutch. 5. Make sure the tubing covers the cable where it exits the display. 6. Route the cable through the channel in the frame, and connect it to the logic board.
Page 43
iBook G4 (14-inch Late 2004) Take Apart - 42 How to Add Spiral Tubing to Protect the Inverter Ca-7.Important: Create enough slack in the cable near the connector to relieve tension on the cable. Secure the connector and cable with a strip of Kapton tape, as shown. 8. Reassemble and test the computer.
Page 44
43 - iBook G4 (14-inch Late 2004) Take Apart DC-In Board DC-In Board Tools • Soft cloth • #0 Phillips screwdriver • Black stick (or other nonconductive nylon or plastic tool) Part Location Preliminary Steps Before you begin, remove the following: • Battery • Bottom case • Bottom shield
Page 45
iBook G4 (14-inch Late 2004) Take Apart - 44 DC-In Board Procedure 1. With the computer on a soft cloth, disconnect the DC-in cable from the underside of the logic board. 2. Remove any tape that holds the cable to the frame or logic board. 3. Route the cable from the guides in the chassis.
Page 46
45 - iBook G4 (14-inch Late 2004) Take Apart DC-In Board 4. Remove the screw from the DC-in board. 5. Tilt up the DC-in board, and pivot it out of the frame. 6. Remove the DC-in board from the computer assembly. 7. Install the replacement DC-in board, and reassemble and test the computer.
Page 47
iBook G4 (14-inch Late 2004) Take Apart - 46 Battery Transfer Board Battery Transfer Board Tools • Soft cloth • #0 Phillips screwdriver Part Location Preliminary Steps Before you begin, remove the following: • Battery • Bottom case • Bottom shield
Page 48
47 - iBook G4 (14-inch Late 2004) Take Apart Battery Transfer Board Procedure 1. With the computer on a soft cloth, remove the two screws that secure the battery connector board to the computer frame. 2. Disconnect the battery transfer board from the logic board. 3. Install the replacement battery transfer board, and reassemble and test the computer.
Page 49
iBook G4 (14-inch Late 2004) Take Apart - 48 Fan Fan Tools • Soft cloth • #0 Phillips screwdriver Part Location Preliminary Steps Before you begin, remove the following: • Battery • Bottom case • Bottom shield
Page 50
49 - iBook G4 (14-inch Late 2004) Take Apart Fan Procedure 1. With the computer on a soft cloth, remove the four screws that secure the fan to the computer frame. 2. Disconnect the fan cable from the logic board. 3. Peel up any tape over the fan bracket or cable. Replacement Note: When reassembling the computer, the replacement fan might include a piece of tape that secures the cable to the body of the fan. Make sure the tape is not blocking the fan blade movement.