Anschutz LaserPower III Short manual for target box

							3
3. Select LaserPower Version „I“:
LaserPower Version „I“.
Handling instruction:
To select the LaserPower version „I“, please press the 
version key [27] two times.
Reaction of the target box:
The fi rst target area [12] from the left of the
target box illuminate for 5 seconds.
State of the target box:
The target box is now set to LaserPower version „I“.
Information:
After pressing the LaserPower „Versions“ button, the user has 60 
seconds from switching on the target box to select the LaserPower 
operating mode. After that time the menu is disabled in order to 
prevent incorrect settings being made during a competition.
GENERAL
Intended use:
The ANSCHÜTZ LaserPower III Set is designed exclusively 
for shooting at the target box [11].
The target is displayed via a light signal to the target box 
and is reset using a remote control device [19]. 
The fi ve-piece target box is designed to record and register 
a specially coded Class 1 laser impulse. 
The design distance for this is 10 meters.
Information:
The LaserPower target box is designed only for indoor use. 
For this reason, it should be protected from moisture. Instruction:
To be considered a hit, the laser beam must be 100% 
within the target area. Edge hits do not count!
4
4.    Setting the brightness of the target areas:
Note:
When starting the LaserPower target box, the brightness 
mode is set to „normal“ intensity (average light intensity).
If you want change the light intensity of the tarket areas [12], 
please follow Step 5 and 6 to get the desired brightness.
Information:
If you press the „brightness button“ [29] a second time, the 
brightness of the target areas will change to maxminum light 
intensity.
5
5.  Setting the brightness of the target areas to maximum light intensity:
Handling instruction:
To adjust the brightness of target areas, please press 
the „brightness button“ [29] on the remote control.
Reaction of the target box:
The target areas of the target box [12] illuminates 
for 2 seconds at maximum strength.
State of the target box:
The target areas of the LaserPower target box are now set to 
maximum brightness. CAUTION: Very high power consumption!
Information:
If you press the „brightness button“ [29] a second time, the 
brightness of the target areas will change to minimum light 
intensity.
6
6.  Setting the brightness of the target areas to minimum light intensity:
Information:
If you press the „brightness button“ [29] a second time, the 
brightness of the target areas will change to medium light 
intensity. Handling instruction:
To adjust the brightness of the target areas, please press 
the „brightness button“ [29] on the remote control.
Reaction of the target box:
The target areas of the target box [12] illuminates
for 2 seconds at minimum strength.
State of the target box:
The target areas of the LaserPower target box 
are now set to minimum brightness.7
Handling instruction:
To delete the hit target areas [12], press the „delete button“ 
[26] on the remote control [19] or wait at least 60 seconds 
(automatic reset).
Reaction of the target box:
The laser power target box sets all target areas to
„No hit“ back (without lighting).
State of the target box:
The laser power target box is now ready for the next match.
7.   Delete the target areas:
After deletion: Target areas without lighting.
Before the deletion: Hit target areas illuminated in white.
8
Handling instruction:
To enter the standby mode (sleep) of the target box, press 
the „On / Standby button“ [28] on the remote control [19]. 
After 3 hours of inactivity, the the target box changes also 
in the standby mode.
Reaction of the target box:
All target areas of the LaserPower target box blink 3 times.
State of the target box:
The target box is now in standby mode (sleep).
8. Standby-Mode of the target box:
Only the complete separa-
-tion of power (power supply, 
lithium battery, or PoE), the 
target box is completely off 
and inactive!
Information: 
To activate the target box 
again, press and hold the
„On / Standby“ button for
at least 1 second.
25  = Infra-red emitter 
26  = „Delete“ button
27
  = „Versions“ button
28  = „On /Standby“ button
29  = „Brightness mode“ button
11   = Target box V 3.1
12   = Target areas (5 in number)
13   = Infra-red receiver
14  = Connector socket power supply 5V
15   = RJ45 external extension interface
16   = RJ45 LAN-PoE network connection
17   = Battery compartment (1x1.5 V AA Lithium)
19   = Infrared remote control
22  = Wall mountings
Defi nition and explanation:
not illuminated
bright / fl ashing,
max. light intensity
bright / fl ashing,
medium light intensity
bright / fl ashing,
minimal light intensity
Remote controle [19]:25
27
26
29
28
  =  On /Standby
  = Delete
  = Brightness mode
  = LaserPower Version
Please note that when use the 
one-button or two Keys remote 
control, only key display func-
tions are available.
Target box [11]:
Front side
Rear side
Bottom side12
22 13
17
14 15 16
1
1.  Commissioning of the LaserPower 
target box:
Handling instruction:
Provide the target box with power: mains unit, Lithium 
battery or PoE (Power over Ethernet – max. cable length 30 m). 
Use only with power supply possible!
Reaction of the target box:
All fi ve target areas [12] of the target box should illuminate 
for 1 second. 
State of the target box:
The target box is now turned on and ready to receive.
Information:
When operating the remote control 
[19] the IR transmitter [25] must 
point towards LaserPower target 
box to ensure proper operation.
Note:
Now the laser power tar-
get box [11] is ready for 
the shooting operation!
USER MANUAL
LASERPOWER
TARGET BOX V3.1
J.G. ANSCHÜTZ GmbH & Co. KG 
Jagd- und Sportwaffenfabrik
Daimlerstrasse 12 
89079  Ulm / Germany
Fon  +49 - (0)731- 40 12 - 0
Fax  +49 - (0)731- 40 12 - 700
www.anschuetz-sport.com
facebook.com/OfficialAnschuetz
„LaserPower Biathlon“   
(also in modified spelling) is a protected brand of 
J.G. ANSCHÜTZ GmbH & Co. KG, Ulm, Germany.   
The unauthorized use of this brand name   
is not allowed and punishable.
Version: 02/2015
Important information
In order to assure a correct hit evaluation and avoid possible  manipulation by laser pointers during competition, only the  laser pulse from a LaserPower rifle will release a hit. 
The LaserPower III target box reacts to the laser pulse of any 
LaserPower III rifle. A definite assignment of a LaserPower III  target box to an individual rifle is not possible.
Same applies to the LaserPower III remote control.  
Each LaserPower III remote control can operate each   LaserPower III aim.
1

1. Inbetriebnahme der LaserPower Zielbox:
Handlung:
Versorgen Sie die Zielbox mit Strom: Externes Netzteil, 
Lithiumbatterie oder PoE (Power over Ethernet – Kabell