American Audio Amplifier VLP Series User Manual

User Instructions
AmericAn Audio®
6122 S. eastern Ave.
Los Angeles ca. 90040
rev. 9/10
Professional Power Amplifier
VLP Series 

This symbol is intended to alert the user to the presence of non insulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to 
constitute a risk of electric shock to persons.
This symbol is intended to alert the user of the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.
CaUtIon: risk of the electrical shock - Do not open!
CaUtIon: To reduce the risk of electrical shock, do not remove...

cAuTion: To reduce THe riSK oF eLecTric 
SHocK, do noT remove THe cover.  
THere Are no uSer ServiceABLe PArTS 
inSide.  reFer ALL Service To Your 
AuTHoriZed AmericAn Audio® deALer.
CaUtIon
Do not open -
risk of electric shockFor  o PT imum   Per Form Ance   And 
re LiAB iL iTY  do no T  P reSen T  TH e 
Am PL iF ier   WiTH  A  SP eAK er  LoAd 
o F   L eS S   T H A n  2   oHm S   o r   AnY 
com Bin AT ion  o F  SP eAK erS  THAT 
ToGeTHer Are LeSS THAn 2 oHmS!
uSin G  one   SPeAK er, iT  mu ST  B e...

Important Precautions
•   To reduce the risk of electrical shock or fire, do not expose this  
   unit rain or moisture.
•   do not spill water or other liquids into or on to your unit.
•   do not attempt to operate this unit if the power cord has been  
   frayed or broken.
•   do not attempt to remove or break off the ground prong from  
   the electrical cord. This prong is used to reduce the risk of elec- 
   trical shock and fire in case of an internal short.
•   disconnect main power before making...

PROFESSIONAL POWER AMPLIFIER
VLP1500
PROCLIP POWER1015
CH A0 dB
106
3
1
80
30
15PRO
CLIP
POWER1015
CH B0 dB
10 6
3
1
80
30
15
1. Channel 1 
gain Control - This rotary knob is used to control the out-
put signal of channel one. Turning the knob in a clockwise direction will 
increase signal output.
2. Channel 1 Protect Indicator - The red Protect Led will begin to glow 
when the channel goes into protect mode. When the channel goes into 
protect mode all output for that channel will turn off. This is to...

PROFESSIONAL POWER AMPLIFIER
VLP300
PRO
CH A
CLIPPOWER
0 dB
1015
106
3
1
80
30
15
POWER1510CLIP
PRO
CH B0 dB
10 6
3
1
80
30
15
11.  Channel  1 
gain  Control  -  This  rotary  knob  is  used  to  control  the 
output  signal  of  channel  one.  Turning  the  knob  in  a  clockwise  direction 
will increase signal output.
12.  Channel  1  Protect  Indicator  -  The  red  Protect  Led  will  begin  to 
glow when the channel goes into protect mode. When the channel goes 
into protect mode all output for...

rear Panel Control
VLP600 & VLP1500
21. Cooling Fans - dual high speed cooling fans
22.  Channel  2  XLr  Input  - channel  two  3-pin  XLr  balanced  input  jack.  See 
page 9 for more details.
23. Channel 2 trS Input - channel two 1/4” female jack.  excepts either a  bal-
anced or unbalanced plug. See page 9 for more details.
24.  Mode  Switch  - This  switch  controls  the  amplifier’s  operating  mode.  The 
amplifier can operate in three different modes;  mono Bridge, Stereo, or Parallel 
mono. The...

rear Panel Control
37. aC Cord - Plug this cable into a standard wall outlet.  check that the voltage 
in your area matches the amplifiers required voltage. 
38. Channel 1 trS Input - channel one 1/4” female jack.  excepts either a  bal-
anced or unbalanced plug. See page 9 for more details.
39.  Channel  1  XLr  input  - channel  one  3-pin  XLr  balanced  input  jack.  See 
page 9 for more details.
40.  Mode  Switch  - This  switch  controls  the  amplifier’s  operating  mode.  The 
amplifier can...

oUtpUts: 
binding post/banana plug - connect your speakers to the binding post outputs on the rear of the amplifier. The 
speaker wire may be connect by bare wire (directly connected, usually for permanent connections), banana plug, 
or spade connector.  connections are made to  channels 1 and 2 output’s for stereo mode or across the red ter-
minals of channels 1 and 2 for mono Bridge mode. 
Important notice:  Although  a  speaker  will  operate  with  the  positive  and  negative  leads  plugged  into...

spade Connector: (Figure 10)
When connecting your speakers to the amplifier using spade connector; unscrew the red and black caps on 
the binding post, be sure not to completely remove or unscrew the red and black caps.  insert the spade con-
nector in to the binding post and tighten the caps down on the spade connector. To reduce the risk of shock 
or  damage  to  your  amplifier,  be  sure  that  the  wire  connected  to  one  binding  post  does  not  come  in  contact 
with that of another. 
When...