Home > Aimco Brakes > Drills > Aimco Brakes URD Series Drills Operation Instructions User Manual

Aimco Brakes URD Series Drills Operation Instructions User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Aimco Brakes URD Series Drills Operation Instructions User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 85 Aimco Brakes manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							URD Series 
    OPERATION INSTRUCTIONS 
    10000 
    SE Pine  Street, Portland,  OR 97216 • (503) 254-6600 • Fax  (503) 255-2615  LIT-MAN680  Rev. 03/2016 
    Printed in USA 
    ©2016 AIMCO It is the responsibility of the employer to place the information on this instruction sheet into the hands of the operator. 
    WARNING
     Always operate, inspect, and maintain this tool in accordance with the American National Standards Institute Safety Code for
      Portable Air Tools 
    (ANSI B186.1) and any other applicable safety codes and regulations.
     Always turn off and disconnect the air supply before installing, removing, or adjusting any accessory on this tool, or before
      performing any 
    maintenance on the tool. F
    ailure to do so could result in injury.  IMPORTANT
     Make sure that these instructions are fully understood before operating this tool. The tool, its attachments, and accessories
      must only be used for their 
    designed purpose. For product liability and safety r easons, any modifications of the tool and its accessories must be agreed upon by the technical 
    authority of the manufacturer. All locally legislated safety rules, with regard to installation, operation, and maintenance s
    hall be respected at all times.  SAFE
    TY RULES  
    1. Inspect and lubricate throttle handle regularly to assure that it operates freely and shuts the tool off consistently when re
    leased.2. Always operate the tool so that body and arm position will allow releasing the throttle in case the drill or reame
    r binds in the hole.3. Do not use a wrench or other aid to operate the throttle.
    4. Do not use the throttle handle to maintain body balance. Use personnel safety harness if the drill is used on elevated work.
    5. Always use safety goggles to prevent eye injury.
    6. Kee
    p all bits, drills, and reamers properly sharpened to minimize possibility of seizing in the work. 7. Use 85 PSI (6kg/cm
    2
    ) air supply at the tool and the recommended hose size to help prevent drill seizing. 8. Make sure that hose and fittings are securely fasten
    ed to prevent injury from a disconnected whipping hose.9. Check for utility lines before drilling into partitions or through flooring.
    10. Do not allow loose clothing like cuffs, shirt sleeves, and shirt tails that could get tangled in the drill bit or spindle.
    11. Use intermittent drill pressure to prevent long, sharp chips.
    12. This drill produces enough torque to cause serious injury. Have the tool secured or held so that if the bit binds in the hole , the torque will not
    cause injury and the throttle can be released.
    AIR SUPPLY
     AIR PRESSURE
    : 85 PSI (6 kgf/cm 2
    ) air pressure is recommended for the most efficient performance.  
    CAUTION
    : Never use higher air pressure to increase the output of the tool.  Overloading will drastically shorten the life of all inter nal parts.  
    LUB
    RICATION  FOR AIR MOTOR
    : Supply light Turbine Oil properly through Air Inlet or line lubricator before and after every operations. For example, Mobil  Turbine Oil #32, Shell Turbine Oil #32 and/or equivalent.  
    FOR GEARS AND BEARINGS
    : Supply recommended high - quality grease (e.g., Shell Alvania No. 2, Mobilplex 2 and or equivalents) once every 
    three months and when the tool is overhauled. Over
    -greasing will cause dull motion or heating. MAINTENANCE
     DRY AND CLEAN AIR
    : Drain daily and install filter at or near th e take off point to prevent trouble from foreign matter.  
    AIR HOSE AND JOINTS
    :  Use air hose (the shorter, the better), joints, and other fittings of good condition and of proper size to avoid pressure 
    drop.
      REGULAR OVERHAUL
    : At least once every three months , a regular or periodical overhaul by a competent person is needed for best performance, 
    trouble free operation, and maximum tool life.
     GENUINE PARTS
    : The use of other than genuine AIMCO replacement parts may result in safety hazards, decreased tool perfor mance, and 
    increased maintenance, and may invalidate all warranties. Use only Uryu’s genuine spare parts for replacement.
     
    AIMCO is not responsible for customer modification of tools for applications on which AIMCO was not consulted. Repairs should  be made only by 
    an authorized AIMCO Service Center. Contact AIMCO at 1-800-852-1368 for the authorized Service Center in your area.  www.aimco-global.com 
    						
    All Aimco Brakes manuals Comments (0)