Home > Aimco Brakes > Nutrunners > Aimco Brakes Nutrunner UOW URW Series Operation Instructions User Manual

Aimco Brakes Nutrunner UOW URW Series Operation Instructions User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Aimco Brakes Nutrunner UOW URW Series Operation Instructions User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 85 Aimco Brakes manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							UOW & URW Series 
    Open-End & Ratchet Wrenches 
    OPERATION INSTRUCTIONS 
    10000 
    SE Pine  Street, Portland,  OR 97216 • (503) 254-6600 • Fax  (503) 255-2615  LIT-MAN670  Rev. 03/2016 
    Printed in USA 
    ©2016 AIMCO  It is the responsibility of the employer to place the information on this instruction sheet into the hands of the operator.  
    WARNING
     Always operate, inspect and maintain this tool in accordance with the American National Standards Institute Safety Code for
      Portable 
    Air Tools (ANSI B186.1) and any other applicable safety codes and regulations.
     Always turn off the air supply and disconnect it before installing, removing, or adjusting any accessory on this tool or befo re 
    performing any maintenance on the tool
    . Failure to do so could result in injury. IMPORTANT
     Make sure that these instructions are fully understood before operating this tool. The tool, its attachments, and accessories
      must only 
    be used for their designed purpose. For product liability and safe ty reasons, any modifications of the tool and its accessories must be 
    agreed upon by the technical authority of the manufacturer. All locally legislated safety rules with regard to installation,  operation, and 
    maintenance shall be respected at all times.
     INSTRUCTIONS FOR CHANGING RATCHETS OR SOCKETS  
    First, follow your local safety regulations strictly on this tool.
     1.
    If needed, adjust the engagement of the operating rod by removing the cam casing and adjusting spacers from the gear casing.
    2. While running the tool, reinstall the cam casing to the gear casing.
    3. Watch the ratchet as the cam casing turns down onto the gear casing. When the ratchet starts to turn, mark its position and
    continue to allow the cam casing to turn down onto the gear casing until the ratchet stops or the cam casing bottoms out.
    4. Turn the cam casing back halfway between the two points and measure the amount of adjusting spacers it will take to take up the
    space between the cam casing and the gear casing. NOTE:
     When changing the socket in the UOW tool, it is very important that the Allen flush head screws are tightened to 30 inch  pounds of torque and Loc-Tite with a 242 thread locker or equivalent. If this is not done, excessive damage will occur to the bevel gear 
    casing and the gears. 
    AIR 
    SUPPLY   LINE SIZE
    : The ID of the air hose should always be one size larger than the air inlet size of the tool.  
    AIR PRESSURE: 
    85 PSI (6 kg/cm2
    ) air pressure is recommended for the most efficient performance. Lower than 57 PSI (4 kg/cm 2 ) 
    may cause the tool
     to malfunction. Too high of air pressure will shorten the life of the tool.  LUBRICATION 
    FOR AIR MOTOR
    : Supply light Turbine Oil properly through Air Inlet or line lubricator before and after every operations. For  example, Mobil Turbine Oil #32, Shell Turbine Oil #32 and/or equivalent.  
    FOR BEARINGS
    : Supply high - quality grease (e.g., Shell Alvania No. 2, Mobilplex 2 and/or equivalent) properly once every three 
    months or when the tool is overhauled.
     MAINTENANCE
     DRY AND CLEAN AIR
    : Drain daily and install f ilter at or near the take-off point to prevent trouble from foreign matter.  
    AIR HOSE AND JOINTS
    :  Use air hose (the shorter, the better), joints, and other fittings of good condition and of proper size to 
    avoid pressure drop.
     REGULAR OVERHAUL
    : Preventativ e maintenance should be performed by a competent repair technician to assure the best 
    performance, trouble
    -free operation, and maximum tool life at least every three months.  GENUINE PARTS: 
    The use of other than genuine AIMCO replacement parts may result i n safety hazards, decreased tool 
    performance, and increased maintenance, and may invalidate all warranties.
     AIMCO is not responsible for customer modification of tools for applications on which AIMCO was not consulted. Repairs should  be 
    made only by an authorized AIMCO Service Center. Contact AIMCO at 1-
    800-852-1368 for the authorized Service Center in your 
    area.  www.aimco-global.com 
    						
    All Aimco Brakes manuals Comments (0)

    Related Manuals for Aimco Brakes Nutrunner UOW URW Series Operation Instructions User Manual