Aimco Brakes Impacts Operation Instructions User Manual

							Impacts  
OPERATION INSTRUCTIONS  
10000 
SE Pine  Street, Portland,  OR 97216 • (503) 254-6600  • Fax  (503) 255-2615  LIT-MAN560  Rev. 03/2016 
Printed in USA 
©2016 AIMCO  It is the responsibility of the employer to place the information on this instruction sheet into the hands of the operator.  
WARNING  
Always operate, inspect, and maintain this tool with American National Standards Institute Safety Code for Portable Air Tool s (ANSI B186.0) and 
any other applicable safety codes and regulations.  
Always turn off the air supply and disconnect the air supply hose before installing, removing, or adjusting any accessories o n the tool or before 
performing any maintenance on this tool . Failure to do so could result in injury.  
Never use higher air pressure to increase the output of the impact wrench. Overloading will drastically shorten the life of a ll internal parts.  
IMPORTANT  
Make sure that these instructions are fully understood befo re operating this tool. The tool, its attachments, and accessories must only be used for their 
designed purpose. For product liability and safety reasons, any modifications of the tool and its accessories must be agreed  upon by the technical 
authority of t he manufacturer. All locally legislated safety rules with regard to installation, operation, and maintenance shall be respect ed at all times. 
The use of sloppy or worn sockets and extensions can cause excessive wear to the impact mechanism and will void wa rranty.  
INSTRUCTIONS FOR SAFE OPERATION  
First, follow your local safety regulations strictly on this tool.  
1. Air power tools can vibrate in use. Vibration, repetitive motion, or uncomfortable positions may be harmful to your hands and   arms. Stop using
an y tool if discomfort, tingling feeling, or pain occurs.
2. Always wear safety goggles.
3. Keep hands, loose clothing, and long hair away from rotating end of the tool.
4. Anticipate and be alert for sudden changes in motion during start up and operation   of any power tool.
5. The tool shaft may continue to rotate briefly after the throttle is released.
6. Do not lubricate the tool with flammable or volatile liquids such as kerosene, diesel or jet fuel.
7. Do not remove any labels. Replace any damaged l abel.
8. Use only impact sockets and accessories. Do not use hand (chrome) sockets or accessories.
9. Impact tools are not torque control devices. Fasteners with specific torque requirements must be checked with suitable torque   measuring
devices after in stallation with an impact tool.
10. Always check for damaged or loose hoses and fittings before operation and replace if necessary. Whipping hoses can cause seri ous injury.
11. Keep body working stance balanced and firm. Do not overreach when operating t he tool.
12. Always wear hearing protection when operating this tool.
13. Do not carry the tool by the hose.
14. Do not force the tool past its rated capacity. Follow tool specifications for choosing proper size and type of accessories. I t will do the j ob better
and safer at the rate for which it was designed.
AIR SUPPLY  
AIR HOSE SIZE :  1/4” NPT air inlet use a 3/8” ID hose; 3/8” NPT air inlet use a 1/2” ID hose; 1/2” NPT air inlet use a 3/4” ID hose; and 3/4”   air 
inlet use a 1” ID hose.  
AIR PRESSURE :  85  PSI (6 kg/cm 2
) air pressure is recommended for the most efficient performance. Too high of air pressure will shorten the life 
of the tool.  
LUBRICATION  
FOR AIR MOTOR :  Supply light turbine oil properly through air inlet or line lubricator before and after ev ery operation (e.g., Mobil Turbine Oil 
#32, Shell Turbine Oil #32, and/or equivalent).  
FOR BEARINGS :  Supply high - quality grease properly (e.g., Shell Alvania No. 2, Mobilplex 2, and/or equivalent) once every three months or when 
the tool is overhauled.  
MAI NTENANCE  
REGULAR OVERHAUL :  At least once every three months, regular or periodical overhaul by a competent repair technician to assure the best 
performance, trouble - free operation, and maximum tool life.  
GENUINE PARTS :  The use of other than genuine AIMCO r eplacement parts may result in safety hazards, decreased tool performance, and 
increased maintenance, and may invalidate all warranties.  
AIMCO is not responsible for customer modification of tools for applications on which AIMCO was not consulted. Repairs  should be made only by 
an authorized AIMCO Service Center. Contact AIMCO at 1 - 800 - 852 - 1368 for the authorized Service Center in your area.  
www.aimco-global.com