Agio International Sling SwivelRocker User Manual

							Page 2IMPORTANT!! PLEASE READ ENTIRE INSTRUCTION SHEET BEFORE ASSEMBLY!!
TO EXPEDITE ANY FUTURE WARRANTY CLAIMS, PLEASE KEEP INSTRUCTION SHEET, WARRANTY CARD AND RECEIPTU BARU METAL
PLATEBOLTPVC BOLT
COVERSPRING
WASHERNUTNOTE: MAKE SURE ARROWS
              FROM BOTH THE U BAR               AND ROCKER ASSEMBLY
              ARE POINTING IN THE               SAME DIRECTION!SEAT DESIGNS MAY 
VARY BUT THE ASSEMBLY 
IS THE SAMEStep 1: Identify all parts packed in carton against the parts list.  Remove all protective materials.
             Place parts on a non-abrasive surface to avoid scratching.  If you are missing any parts or are             unsure as how to proceed with the assembly, call our Customer Service Center at             1-800-416-3511.  Do not attempt assembly if any parts are missing or damaged.
             Step 2: Place the swivel base (with rocker assembly) on a flat, solid surface.  Make sure the rocker
             assembly is positioned all the way into the base.  It may have shifted or vibrated out during             shipment.             Step 3: Important: We recommend 2 people work together to assemble the chair.  Note the
             arrow labels on the U bar and the rocker assembly.  Also note the horseshoe shape of the
             rocker plate.  Point the open end of the horseshoe away from you.  The arrows on the rocker             assembly should be pointing towards you.  Set the chair frame on the rocker assembly with             front of the seat facing you and the arrows on the U bar pointing towards you as shown             in Figure 1.  This is very important for a safe, balanced rocking motion.  If chair frame has
             been properly positioned on the rocker assembly, all arrows on the U bar and rocker
             assembly will be pointing in the same direction.             Step 4: Critical Step: The U metal plates must be installed in the proper location.  Read this
             step and carefully examine.  Insert the U metal plate, so that the U bar and rocker plate             are between both sides of the U metal plate.  Make sure that the holes in the U metal             plate are completely aligned with the holes in the U bar as shown in Figure 1.  Guide the
             bolts through the holes on the top side of the U metal plate, through the holes in the             U bar portion of the chair, through the holes in the rocker plate and then, most importantly,             through the holes in the bottom side of the U metal plate.  It is very important that the             holes in the bottom portion of the U metal plate be placed directly beneath the holes in the             rocker plate.  Add a spring washer and a nut to each bolt as shown in Figure 2.  Hand
             tighten nuts 3-4 revolutions only.  Repeat the same procedure on the other side.
                          CAUTION: Failure to place U metal plates under the rocker plates and above the
             U bar exactly as shown in diagram will cause the bolt heads and nuts to damage the             structure of the rocker plates and the U bar.  Damage due to over tightening of bolts
             or improper assembly could cause injury and may void your warranty.
             Step 5: Tighten all nuts and bolts with the hex wrenches provided.  Do not over tighten.  Remove
             arrow labels from U bar and rocker assembly.  Cover bolts with PVC bolt covers.             Step 6: Your chair should be ready for use.  If your chair is not rocking properly, double-check your
             assembly procedure, especially Step 3.  If the chair rocks too far forward to or is difficult to             rock backwards, you  have probably installed the seat frame backwards on the rocker             assembly.  If you need further assistance, please call our Customer Service Center             at 1-800-416-3511.
   IMPORTANT NOTE:  Damage to welds or frames resulting from over tightened bolts or 
improper assembly is not covered under our warranty. Please read all instructions carefully
before assembly.  If you have any questions regarding your assembly, call our Customer 
Service Center at 1-800-416-3511.FRON
T
F
RONTFigure 1Figure 2U BARFRPROCKER
ASSEMBLYQTYSWIVEL BASE &
ROCKER
ASSEMBLY5/16 X 40 MM
BOLTE8.0 X 2.3 MM 
SPRING WASHERHW00035/16 NUTHW0015U METAL
PLATECHAIR FRAMEPARTS LISTDESCRIPTIONORDER PART #244411HW0295HW029650-49661-1QTYPARTS LISTDESCRIPTIONORDER PART #PVC BOLT COVERHW00288FOOT CAP
FACTORY ASSEMBLYHEX WRENCH-1HW00081HEX WRENCH-2HW00071FRP
FACTORY ASSEMBLYG0009FC0004SWIVEL BASEFOOT CAPSLING TUBE CAP
FACTORY ASSEMBLYFC0046PVC BOLT
COVERAR1094AR1095