Accusplit Stopwatch A601X3V Battery Instructions User Manual

							1.	 Turn	the 	watch 	over 	and 	select 	the 	correct 	si\fe 	Phillips 		
	 screwdriver	(the	\bastening	is	very	tight,	so	the	screws	 	
	 will	strip	easily	i\b	you	use	the	wrong	si\fe	or	type	o\b		
	 screwdriver).
2.	 Remove	all	six	screws	\brom	the	back	o\b	the	case,	and		
	 set	aside	so	they	will	not	get	lost.
3.	 Gently	pry	the	watch	back		
	 away	\brom	the	case	\bront,		
	 using	the	gap	near	the		
	 middle	button.	 The	electronics		
	 module	will	come	away	with		
	 the	case	back.	 You	will	have		
	 to	slide	the	back	downwards		
	 to	\bree	the	electronics	module		
	 \brom	the	button	actuator	bars.		
	 The	lanyard	will	also	come	loose	-	set	it	aside.	
4.	 Hold	the	case	back	with		
	 electronics	module	\bace	up		
	 in	one	hand.	Use	your	other		
	 hand	to	gently	pull	the		
	 electronics	module	loose		
	 \brom	the	case	back.	 The		
	 green	circuit	board	will		
	 come	away	with	the	module.		
	 Try	to	leave	the	gray	rubber		
	 gasket	in	place	(see	step	7).
5.	 Turn	the	electronics	module	over	to	see	the	battery.		
	 Use	a	small	flat	head	screwdriver	to	gently	push		
	 the		silver	battery	hold-down	tab	out	o\b	the	way	(it		
	 is	held	in	place	with	spring	tension).	 With	the		
	 battery	hold-down	tab	out	o\b	the	way,	you	can		
	 shake	or	pry	the	old	battery	loose.
6.	 Install	a	new	CR2032	battery	with	+	terminal		
	 \bacing	up. 7.	 I\b	the	gray	gasket	came	loose	\brom	the	case	back,		
	 reinstall	it	now.
	 a.	 First,	line	up	the	black	gasket	holder	on	top	o\b	the	
	
	 	 case	back,	with	the	beveled	side	\bacing	up.
		 b.	 Orient	the	gasket	correctly.	 The	three	dark	gray		
	 	 pads	must	be	\bacing	up	(away	\brom	the	case		
	 	 back).
					 c.	 Finally,	put	the	gasket	on	top	o\b	the	gasket		
	 	 holder,	and	gently	push	both	into	the	case	back		
	 	 until	they	pop	into	place.	
8.		 Turn	the	electronics	module	over	so	that	the	battery	 	
	 is	\bacing	the	inside	o\b	the	case	back.	Gently	push	the	 	
	 electronics	module	down	into	the	gray	rubber		
	 gasket,	until	it	seats.	It	will	be	firmly	in	position	i\b		
	 this	is	done	correctly.
9.	 Slide	the	button	set	out	o\b	the	\bront	case	(you’ll	see		
	 that	the	three	buttons	are	joined	together	into	one		
	 assembly).	
10.	 Turn	the	button	actuator	set	so	that	the	flat	part	o\b		
	 the	buttons	are	\bacing	the	outside	o\b	the	case	back.		
	 Now,	slide	the	button	set	into	the	top	o\b	the	case		
	 back	&	electronics	module	assembly,	so	that	the		
	 button	actuator	bars	slide	down	into	the	slots		
	 between	the	top	o\b	the	gray	rubber	gasket	and	the		
	 case	back.
11.	 Now,	pick	up	the	case	\bront,	holding	it	so	that	the		
	 outside	(\bront	o\b	the	watch)	is	touching	your	palm.		
	 Put	the	lanyard	back	into	its	slot	in	the	bottom	o\b		
	 the	case	\bront.	
12.	 Flip 	the 	electronics/case 	back 	assembly 	over 	and	 	
	 gently 	press 	it 	back 	into 	the 	\bront 	case 	o\b 	the 	watch,	 	
	 until 	it 	seats. 	The 	buttons 	should 	now 	work 	normally.
13.	 Replace	and	tighten	the	six	screws	in	the	case	back.	 	
	 Screws	must	be	tight	\bor	the	watch	to	be	water		
	 resistant	again.
	
	
ACCUSPLIT®
A601X3V Stopwatch 
Batter\f Chang\bng Instruct\bons
When	the	display	on	your	watch	begins	to	go	dim,	or	i\b	it	goes	blank,	the	watch	needs	a	new	battery.	
The	watch	uses	a	high	capacity	CR2032	Lithium	battery,	which	has	an	expected	li\be	o\b	more	than	five	
years	in	this	watch.	
To	change	the	battery,	you	will	need	a	set	o\b	large	jeweler’s	screwdrivers	(including	Phillips	head).	
Note:	I\b	this	looks	too	complicated,	you	can	always	send	your	watch	back	to	 ACCUSPLIT	\bor	battery	
changing	instead.		See	www.ACCUSPLIT.com/support	\bor	details.
	
9:4953
ACCUSPLIT, Inc. (Support/Repair)  •  3090 Independence Drive, Suite 148  •  Livermore, CA 94551 USA
800-935-1996  •  925-290-1900  •  FAX 925-290-1930  •  www.ACCUSPLIT.com  •  [email protected]
998-310
Electronics	module
BatteryGray	rubber	
gasket
Battery	hold-down	tab