Accusplit Pedometer AX2770 User Manual

							ACCUSPLIT, Inc.
7901 Stoneridge Drive, Suite 350 Pleasanton, CA  94588
800-935-1996  •  925-290-1900  •  FAX 925-290-1930
www.ACCUSPLIT.com  •  [email protected]
Eat Right! Walk More! Live Well!  The ACCUSPLIT Lifestyle
181-1603
ACCUSPLIT AX2770 
Accelerometer Pedometer INSTRUCTIONS
  
Congratulations on taking the first step 
to wellness with your purchase of an 
ACCUSPLIT Accelerometer pedometer.  It’s easy to set up your new pedometer.  Just follow the steps below, and start walking!
FUNCTIONS
•  Accurate Step Count at every angle of Tilt!
•  Automatic Activity Timer for Step Activity, up
   to 100 Hours to One Second
•  Adjustable Moderate-to-Vigorous Pace Filter 
  (default setting is 110 steps per minute, SPM) 
  to capture ALL (adjust to 70 SPM) or just 
  certain MV Step Activity Time (up to 140 SPM).
•  5 second Display Accuracy Filter prevents 
  recording false steps
• 2 new features help keep power consumption low:
  Hibernate Mode: From factory to user
  Sleep Mode: After 5 minutes of no activity
•  Distance and Calorie computations on new 
  tracking web site
FEATURES
•  AX2770 Our New low power accelerometer 
  with PedometerEngine™TW20
•  Certified Accurate
•  Ultra Thin case
•  Over 3 year battery power-an unheard of 
  feature in pedometers with accelerometer 
 sensors
•  Magnum display digits for easy viewing
•  ACCUSPLIT’s 5-Year Dual, No Proof and 
  Proof of Purchase Limited Warranty
WEARING YOUR PEDOMETER
Gently slide the pedometer onto your belt or the top edge of your pants or skirt. 
It should fit snugly and level, above one knee. The strong clip makes it easy.
Note: Your accelerometer pedometer no longer needs to be as vertical as possible.
The cover should be closed to minimize 
objects hitting your pedometer. To avoid 
losing or dropping your pedometer, use 
the included leash and clip to fasten the 
pedometer securely to your clothing.
ATTACHING THE LEASH
Attach the pedometer to the leash by 
looping the leash through the pedometer 
clip. Next, loop the leash through the 
metal clip, then clasp the waistband of 
your clothing with the pedometer belt 
clip.  
Note: You can also use a safety pin to 
fasten the leash to your clothing, loop 
the leash through your belt or belt loop, 
or use a badge holder.
POWER UP and DISPLAY ON
Power UP the display, initially, from its battery saving, factory set, “hibernate mode”, 
by pressing a button for 2 seconds, until you see the display digits, then release the button.
Turn ON the display, from its battery saving “sleep mode” (which it enters after 
5 minutes of no STEP counting) by moving your pedometer.
DISTANCE & CALORIE COMPUTATIONSThe computations of Distance and Calories can be done at the tracking web site, 
WALKING10000.org, when the STEP & ACTIVITY TIMES are tallied.
VIEWING YOUR RESULTS
Once you put on your pedometer with the cover closed, it will automatically 
begin to record your steps, and activity time. Repeatedly press the MODE 
button to cycle through the pedometer modes: 
STEP →  MV ACTIVITY TIMER  →  STEP
5-Second STEP DELAY FILTER
ACCUSPLIT has added a “5-second step delay filter” to reduce the counting of “false steps”. 
When beginning walking, the display will not show any “tallying of new steps,” until after 
5 seconds of walking. Then, all the STEPS will be added to the display and new STEPS 
continue to be counted and displayed.
RESETTING YOUR PEDOMETER
Most people prefer to reset step counts daily. To reset: press and hold the 
white RESET button for at least 2 seconds.
REPLACING THE BATTERY
When the display starts to dim or goes blank, it is time to replace the battery. Your pedometer uses 
one Type CR2032 3 volt battery. 
To replace:
1. Insert a coin between the cover and the hinge and pop cover off.
2. Remove the old battery and insert the new battery, + side up.
3. Carefully replace the battery door, hooking tabs at top, then carefully pushing 
    the cover down until it snaps shut at the bottom edge.
DISPLAY MODES
•  STEP count mode shows your STEP count since last 
  RESET. up to 1,000,000 STEPs.
•  Activity TIMER MODE shows accumulated Activity 
  TIME in Hours, Minutes and Seconds since last RESET, 
  up to 100 Hours. The timer runs automatically whenever 
  STEPs are being recorded.
 
ACTIVITY TIME ADJUSTMENT - STEPS PER MINUTE (SPM)
Note that the default value of the Moderate-to-Vigorous 
(MV) Activity Pace Filter is set at a walking pace of 110 Steps 
Per Minute (SPM).
If you want ALL Step Activity Time to be recorded, adjust the SPM to the lowest setting, 
70 SPM pace. But, if you desire to record only the most vigorous Step Activity Time, 
adjust to 140 SPM. 
To adjust SPM, view the MV Display, then hold down the SPM button until the digits 
stop flashing. 
Then, push the SPM button until you see the desired SPM pace. 
Push MODE to return to regular operating mode.
MODE
SPMRESET
+/–y