Accusplit Pedometer AE2700 SERIES User Manual

							
DISPLAY MODES 
• step: STEP mode shows your step count 
  since last reset, up to 100,000 steps. 
•  mi: DISTANCE mode 
(2740, 2790 only) 
  shows distance walked or jogged since 
  last reset.
•  kcal: CALORIE mode 
(2790 only) shows 
  calories burned through step activity 
  since last reset.
•  AM/PM: CLOCK mode 
(2790 only) 
  shows time of day.
•    ACTIVITY TIMER MODE shows total activity time 
  in minutes and seconds since last reset. The timer runs automatically 
whenever steps are being recorded.
SETTING UP YOUR PEDOMETER 
To record your distance and calories 
accurately, you will need to set your stride 
length and body weight. 
Finding Your Stride Length (2740, 2790 
only): Your stride length is the length of one 
of your steps, measured from “toe to toe.” 
To measure, walk 10 steps with your normal 
stride and measure the TOTAL DISTANCE 
from the toe of your starting step to the toe 
of your 10th step (see diagram below). Divide 
the TOTAL DISTANCE by 10, and multiply 
the decimal portion by 12 to find your stride 
length in feet and inches. Example: If you 
walk 23 feet in 10 steps, your stride length 
is 2.3 feet. Multiply 0.3 x 12 = 4. Your stride 
length is 2 feet, 4 inches.
Setting Your Stride Length (2740, 2790 
only): Repeatedly press the red MODE 
button until “mi” appears. Press the blue SET 
button once to enter setting mode. Display 
will shift to show stride, in feet and inches. 
Press and hold down the blue SET button to 
increase stride length. Press the red MODE 
button to exit setting mode. 
Note: Pressing the white RESET button 
resets stride length to 2' 0". 
Setting Your Weight (2790 only): Repeat-
edly press the red MODE button until “kcal” 
appears. Press the blue SET button once 
to enter setting mode, then press and hold 
the blue SET button to increase weight (in 
pounds). Press the red MODE button to exit 
setting mode. 
Note: Pressing the white RESET button 
resets weight to 120 lbs.
Setting the Clock (2790 only): Repeatedly 
press the red MODE button until “AM” or 
“PM” appears. Press the white RESET 
button. The dash will stop flashing. Press 
and hold down the red MODE button until 
the correct hour is displayed; release button. 
Press and hold down the blue SET button 
until the correct minutes are displayed; 
release button. Press the white RESET button 
to exit setting mode. The dash will begin 
flashing. The clock is now set.
WEARING YOUR PEDOMETER
While gently holding the belt clip open, slide 
the pedometer onto your belt or the top edge 
of your pants or skirt. It should fit snugly and 
level, above one knee. 
Note: The pedometer should be as vertical as 
possible. Walkers with larger stomachs may 
find it helpful to wear the pedometer farther 
back on the body, toward one hip. The cover 
must be closed for the pedometer to work. 
To avoid losing or dropping your pedometer, 
use the included leash and clip to fasten the 
pedometer securely to your clothing. 
Attaching the Leash: Attach the pedometer  
to the leash by looping the leash through the  
pedometer leash slot. Next, loop the leash 
through the metal clip. Finally, clasp the waist-
band of your clothing with the metal clip. You 
can also use a safety pin to fasten the leash to 
your clothing, loop the leash through your belt 
or belt loop, or use a badge holder. 
ACCUSPLIT AE2700 Series Pedometer
(AE2720, AE2740, AE2790)
INSTRUCTIONS
ACCUSPLIT, Inc.  •  2290M Ringwood Ave.  •  San Jose, CA 95131
800-965-2008  •  925-226-0888  •  FAX 925-463-0147  •   www.ACCUSPLIT.com   •  [email protected]
VIEWING YOUR RESULTS
Once you put on your pedometer with the 
cover closed, it will automatically begin 
to record your steps, distance (2740, 
2790 only), calories burned (2790 only), 
and activity time. Repeatedly press the 
red MODE button to cycle through the 
pedometer modes: 
STEP → DISTANCE → CALORIE → CLOCK 
→ ACTIVITY TIMER → STEP
RESETTING YOUR PEDOMETER
Most people prefer to reset step, distance, 
and calorie counts daily. To reset: From 
STEP, DISTANCE, or CALORIE mode, press 
and hold the white RESET button for at least 
2 seconds.
REPLACING THE BATTERY
When the display starts to dim or goes 
blank, it is time to replace the battery. Your 
pedometer uses one Type L1142 (LR43) 1.5 
volt silver oxide battery. To replace:
1.  Insert a coin into the slot on the front of 
the case, and twist counterclockwise to 
loosen the battery door.
2.  Remove battery door and take out the 
old battery. Replace it with a new battery. 
The battery’s positive (+) terminal should 
be FACE UP while you put it into the 
pedometer.
3.  Put the battery door back on and twist the 
coin clockwise to tighten.
Eat Right! Walk More! Live Well! 
The ACCUSPLIT Lifestyle
Congratulations on taking the first step to wellness 
with your purchase of an ACCUSPLIT pedometer. 
It’s easy to set up your new pedometer. 
Just follow the steps below, and start walking!
Red: MODE
9789
Blue: SET (2740, 2790 only)
White: RESET 
10 steps
970-048
First, loop thepedometer leash slot
Next, loop the metal clip, then clasp clothing
Or, loop a  badge holder,  then put into pocket(Badge holder  not included)Or, loop a belt or belt loop