Acco Nobo Projector S17E User Manual

							English
11
Introduction
Wireless Remote Control
1. IR LED
2. Power/Standby
3. Re-Sync 
4. Display Mode
5. Keystone Correction
6. Number Buttons
(for password input) 
7. Clear 
(for password input)
8. DVI
9. Video Source
10. S-Video Source
11. Source Lock 
12. VGA Source
13. Color Setting
14. Menu
15. Enter
16. Four Directional 
Select Keys
17. Brightness
18. Zoom
19. Display Format
20. Hide
21. Freeze 
 21
1
 4
 5
 6
 9
2
 7
 8
 3
 15
 13
 12
 16
 14
 17
 18
 19
 20
 10 11

						

							English
12
Installation

						

							English
13
 Installation
Powering On the Projector
1.  Remove the lens cap. n
2.  Ensure that the power cord and signal cable are securely 
connected.  The Power LED will Flash Green.
3.  Turn on the lamp by pressing “Power/Standby” button on 
the control panel.o And the Power LED will turn Green.
The fi  rst time you use the projector, you can select your 
preferred language from quick menu after the startup screen 
display.
4.  Turn on your source (computer, notebook, video player,etc.).  
The projector will detect your source automatically.

						

							English
14
Installation
Warning Indicator

						

							English
15
 Installation
 Adjusting the Projected Image
Adjusting the Projector Image Height
Tilt Adjusting 
Feet Elevator Foot
23
Elevator Button
The projector is equipped with an elevator foot for adjusting the 
image height.
  To raise the image:
1.  Press the elevator button 
n.
2.  Raise the image to the desired height angle o, then release 
the button to lock the elevator foot into position.
3. Use 
p to fi  ne-tune the display angle. 
  To lower the image:
1.  Press the elevator button.
2.  Lower the image, then release the button to lock the eleva-
tor foot into position.
3. Use 
p to fi  ne-tune the display angle.
3
 1 
						

							English
16
Installation
69.3
(176.1cm)115.6
(293.5cm)161.8
(410.9cm)184.9
(469.6cm)277.3
(704.4cm)
38.1
(96.8cm)76.2
(193.6cm)127.1
(322.7cm)177.9
(451.8cm)203.3
(516.3cm)304.9
(774.5cm)
4.9
39.4 26.3 23.0 16.49.8(1.5m)
(12.0m) (8.0m) (7.0m) (5.0m) (3.0m)34.7
(88.1cm)
Width
Height
Dia
gonal
Max.38.1(96.8cm)76.2(193.6cm)127.1(322.7cm)177.9(451.8cm)203.3(516.3cm)304.9(774.5cm)
Min. 34.7(88.1cm) 69.3(176.1cm) 115.6(293.5cm) 161.8(410.9cm) 184.9(469.6cm) 277.3(704.4cm)
Max.(WxH)30.5 x 22.9
(77.4 x 58.1cm)61.0 x 45.7
(154.9 x 116.2cm)101.7 x 76.3
(258.2 x 193.6cm)142.3 x 106.7
(361.4 x 271.1cm)162.6 x 122.0
(413.0 x 309.8cm)243.9 x 182.9
(619.6 x 464.7cm)
Min.(WxH)27.8 x 20.8
(70.5 x 52.9cm)55.4 x 41.6
(140.9 x 105.7cm)92.5 x 69.4
(234.8 x 176.1cm)129.4 x 97.1
(328.7 x 246.5cm)147.9 x 110.9
(375.7 x 281.8cm)221.8 x 166.4
(563.5 x 422.6cm)
4.9(1.5m)9.8(3.0m)16.4(5.0m)23.0(7.0m)26.3(8.0m)39.4(12.0m)
Screen
(Diagonal)
Screen 
Size
Distance
Diagonal
Adjusting the Projector Zoom / Focus
You may turn the zoom lever to zoom in or out.  To focus the im-
age, rotate the  focus ring until the image is clear. The projector 
will focus at distances from 4.9 to 39.4 feet (1.5 to 12.0 meters) 
with mechanical travel.
Adjusting Projection Image Size

						

							English
17
 User  Controls
 Control Panel & Remote Control
There are two ways for you to control the functions: Remote 
Control and Control Panel.
  Using the Control Panel
 Power/Standby  
4 Refer to the “Power On/Off the Projector” section on pages 13-
14.
 
Source  
4 Press “Source” to choose RGB, Component-p, Component-i, S-
Video, Composite Video and HD sources.
 
Menu 
4 Press “Menu” to launch the on screen display (OSD) menu. To 
exit OSD, press “Menu” again.
 Keystone /
4 Adjusts image distortion caused by tilting the projector (±16 
degrees).
 
Four Directional Select Keys
4 Use        to select items or make adjustments to your 
selection.
 
Enter 
4 Confi  rm your selection of items.
 Re-Sync 
4 Automatically synchronizes the projector to the input source  
(for PC signal only).
Control Panel 
						

							English
18
User Controls
  Using the Remote Control
         Power/Standby
 4 Refer to the “Power On/Off the Projector” section on pages 13-
14.
  Re-Sync (for PC signal only)
 4 Automatically synchronizes the projector to the input source.
 Hide
 4 Press “Hide” to hide image, press again to restore display of the 
image.
 Display Format
 
4Display the “Display Format” section of the on screen display 
menu to select the desired aspect ratio.
 Freeze
 
4 Press “Freeze” to pause the screen image.
 Display Mode
 
4 Select the Presentation, Bright, Movie, sRGB and User.
 Keystone   / 
 4 Adjusts image distortion caused by tilting the projector (±16 
degrees).
 Brightness
 
4Adjust the brightness of the image
.
 Zoom
 4 Press “+ / -” button to zoom in/out of an image.
  Four Directional Select Keys 
 
4 Use         to select items or make adjustments to your 
selection.
 Enter
 4 Confi  rm your selection of items.
 Menu  
 4 Press “Menu” to launch the on screen display menu.  To exit 
OSD, press “Menu” again.
Remote Control 
						

							English
19
 User  Controls
 Clear
 
4Clear your input of password.
 Color Setting
 
4Adjust the Red, Green, Blue, Yellow, Cyan and Magenta colors 
for advanced adjustment of the individual colors.
 Source Lock
 
4Select auto detection all connector ports or lock current connector 
port.
 VGA
 4Press “VGA” to choose VGA connector.
 S-Video
 4Press “S-Video” to choose S-Video source.
 Video
 4Press Video to choose composite video source. 
						

							English
20
User Controls
The Projector has multilingual On Screen Display menus that 
allow you to make image adjustments and change a variety of 
settings. The projector will automatically detect the source. 
How to operate 
1.  To open the OSD menu, press “Menu ” on the Remote Control 
or Control Panel.
2. When OSD is displayed, use     keys to select any item in the 
main menu.  While making a selection on a particular page, press 
 or “Enter” key to enter sub menu.
3. Use      keys to select the desired item and adjust the settings 
by 
    key.
4. Select the next item to be adjusted in the sub menu and adjust as 
described above.
5. Press “Menu ” to confi  rm, and the screen will return to the main 
menu.
6.  To exit, press “Menu ”again. The OSD menu will close and the 
projector will automatically save the new settings.
 On Screen Display Menus
Main Menu
Sub Menu
Setting