3M Multimedia Projector Mp7740 Operators Manual

113M™ Multimedia Projector MP7640
© 3M IPC 2000
MENU
SELECT
STANDBY/ON VIDEO
POSITION
MAGNIFY FREEZE VOLUME
MUTE
BLANK TIMER AUTORGB
MENURESET
Section 2: Product Description
STANDBY/ON
Turn on Main Power switch.
Press STANDBY/ON button to
begin projection mode (lamp on)
or press and hold button for one
second to switch to standby
mode (lamp off).
MENU SELECT
Press to select menu items.
MENU Buttons
Press to navigate among menu
items.
MENU
Press to display the menu
screen.
MAGNIFY*
Press MAGNIFY (+) to...

3M™ Multimedia Projector MP764012© 3M IPC 2000
Changing Remote Control Battery
This remote control transmitter uses a lithium battery located in a sliding holder inserted into the bottom of
the transmitter.
1. Turn the remote control transmitter over to access the battery holder.
2. Push the smaller tab inward as indicated below.
3. Slide the battery holder out of the bottom of the transmitter.
4. Lift the battery out of the holder and replace with the new battery. Make sure the “+” side is facing up.
5....

133M™ Multimedia Projector MP7640
© 3M IPC 2000
1. Press and hold the STANDBY/ON button        for one second. The ON indicator blinks orange and
the lamp turns off. After approximately one minute, the fan stops and the indicator stays orange.
2.Turn off the MAIN POWER SWITCH.
3.Close the sliding lens door.
Caution
Projector Start-up
Section 3: Basic Operations
Figure 3.1 Projector Controls
1. Make all equipment and cable connections with the power off.
2. Turn on the MAIN POWER SWITCH       of the...

3M™ Multimedia Projector MP764014© 3M IPC 2000
How to Use Height Adjustment Foot
Section 4: Adjustments and Functions
Adjust the image elevation and projection angle (within 0 to 10°) using the height adjustment foot at the
front of the projector.
1. Raise the front end of the projector so the foot is not touching the tabletop.
2. Push the lock button on the left side of the projector to unlock the foot.
3. Extend or retract the foot to the desired height.
4. Release the lock button to lock the foot into...

153M™ Multimedia Projector MP7640
© 3M IPC 2000
Section 4: Adjustments and Functions
Plug & Play Function
Plug & Play is a system configured with peripheral equipment (including a computer and display), and a
compatible operating system. This allows the user to connect various peripheral equipment successfully
without having to adjust settings manually. The equipment and projector exchange this information automati-
cally. This projector is VESA DDC (Display Data Channel) 1/2B compatible. Plug & Play is...

3M™ Multimedia Projector MP764016© 3M IPC 2000
Section 4: Adjustments and Functions
Menu Navigation
Factory Default Setting:
To reset a single item from SETUP menu:
1. Select the adjustment item (Bright, Contrast...).
2. Press the RESET button.  Only the selected item
resets. 1. Press MENU disk button on projector or remote control MENU buttons.
On-screen menus are displayed on the projected image.
2. Select the menu to be adjusted using the MENU disk button or remote control Menu buttons           ....

173M™ Multimedia Projector MP7640
© 3M IPC 2000
Section 4: Adjustments and Functions
Figure 4.4 RGB signal input Figure 4.5 Video signal input
*Auto Sync Function: Press the AUTO button on the remote control to engage the automatic sync function.
The message “AUTO IN PROGRESS” will display for several seconds as the projector adjusts the V. POSIT,
H.POSIT., H.PHASE, and H. SIZE settings. Auto Sync can also be executed from the control panel key pad.
Press and hold the RESET button, then press the INPUT...

3M™ Multimedia Projector MP764018© 3M IPC 2000
Section 4: Adjustments and Functions
INPUT Submenu
The INPUT submenu is used to select the RGB or video input source. The RGB values are shown in Figure
4.6. The Video values are shown in Figure 4.7.
Figure 4.6 RGB Input Submenu
Figure 4.7 Video Input Submenu
Adjustment
Area
RGB
Video
AutoValue
Displays the following RGB inputs:
FH:  horizontal sync frequency
FV:  vertical sync frequency
Selects the VIDEO signal format Auto,
NTSC, PAL, SECAM,
 NTSC 4.43,...

193M™ Multimedia Projector MP7640
© 3M IPC 2000
IMAGE Submenu
The IMAGE submenu is used to change the image characteristics.
Figure 4.9 Image Adjustment Screens
Adjustment                                                         Value
Screen
KEYSTONE
Reduce distortion Reduce distortion
at bottom of image. at top of image.
BLANKSelects the blank screen color: red, orange, green, blue, purple, white or black.
MIRRORInverts the picture horizontally or vertically.
H:  INVERT Inver ts the picture...

3M™ Multimedia Projector MP764020© 3M IPC 2000
OPT. Submenu
The OPT. submenu allows you to control communication function.
Figure 4.10 OPT Adjustment Screens
Adjustment                                           Value Default
Screen
VOLUMEAdjusts the loudness of audio coming through the speaker.8
Selects the background color in which the menu system will be displayed.
MENU COLORChoice of red, orange, green, blue, purple, white and black. Blue
(All menus have white text except white menu, which will have...