Home > 3M > Locator > 3M DynatelTM 2250MMiD Cable Locating Quick Reference Guide

3M DynatelTM 2250MMiD Cable Locating Quick Reference Guide

    Download as PDF Print this page Share this page

    Have a look at the manual 3M DynatelTM 2250MMiD Cable Locating Quick Reference Guide online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 307 3M manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							
    3M DynatelTM 2250M/M-iD  
    Cable Locating Quick Reference Guide 
     [1] POWER: Turns unit off and on. 
    [2] SPEAKER:  Adjusts the volume of the receiver 
    [2A] SPEAKER ICON:  Indicates the volume level of  
          receiver.   
      
    Telecom Access Division 
    6801 River Place Blvd. 
    Austin, TX 78726-9000 
    800-426-8688 
    http://www.3M.com/dynatel 
         78-8135-5016-3  Rev. A 
    [3] CONTRAST: Adjust contrast of screen 
    [4] GAIN: Adjust the sensitivity of the receiver 
    [5] LOCATE/OK:  Sets the receiver to cable locate mode. 
          Acknowledges setup entries (OK) 
    [6] MENU: Displays screens for configuration of the unit, 
          i.e.: clock, depth units, etc. 
    [7] BACKLIGHT: Toggles the backlight low, high, and  
          off. 
    [8] BATTERY ICON:  Indicates battery level. 
    [SK] SOFTKEYS: The function of each Softkey is shown  
          above the key on the screen. 
    [9] SOFT KEY COMMAND:  Definitions for each of the four 
    soft key functions. 
     
    [10] SIGNAL STRENGTH: Digital reading of the signal the  
          receiver is detecting. 
    [11] BAR GRAPH:  Graphical representation of the  
          received signal. 
    [12] Gain Level:  Displays the relative gain level. 
     
     
    Set Cable/Pipe Locate   
    1.  Press Power [1]  
    2.  Press Locate [5]  
    3.  Press Softkey [SK] for Cable/Pipe 
     
    Set Frequency of Receiver  
    1.  From the Cable locate screen, press 1st SK (Freq). 
    2.  Toggle SK of group of frequencies  
    (Active Power, Passive, or Aux) until the desired 
    frequency is displayed. 
    3.  Press Locate/OK [5] to return to locate mode.  
     
    Select Locate Mode 
    There are three locate modes (DirPk, DirNull, and SplPk).  
    The most common mode of cable locating is DirPk. 
    Press 2nd  [SK] (Mode) to display DirPk. 
     
    Locate Target Cable 
    Target Path will be indicated by:  
    The highest numerical signal strength [10] 
    A closed bar graph [11] 
    Both directional arrows 
     
    Depth and Current 
    1.  Rest the tip of the receiver on the ground over target cable. 
    2.  Press the [SK] Depth from the locating screen.  
    3.  Verify target with depth measurement and relative 
    current reading. 
    4.  Press Locate [5] to return to locating screen. 
     
    Transmitter operational instructions are located inside the cover of the transmitter. 
    1
    Cable Locate
    Freq ModeDepth
    Alert577 Dir Pk O f f
    2
    Select Freq. Press Locate
    Active Power Aux57760%
    Pasv60L 560CATV
    Cable Locate
    Freq ModeDepth
    Alert577 Dir Pk O f f
    Cable Locate
    Freq ModeDepth
    Alert577 Dir Pk O f f
    86.9dB
    60%
    1
    Marker Cable /
    Pipe Tone / 
    Ext 
    3
    2250M Cable/Pipe/Fault Locator
    OK Menu
    Gain Adjust
    Spkr/Xpand
    On/Off
    Dynatel
    TM
    Cable Locate
    Freq Mode Depth
    Alert577Dir Pk O f f
    86.9dB
    60%
    Locate
    10
    7
    4
    6
    5
    2A8
    113
    2
    1
    SK
    12
    9
    xpnd
    2OK
    OK3
    Mem
    Select Sonde
    Depth
    Cable Depth
    D epth      C urrent12 in7829.30mA
    Depth
    1-ShotCable Locate
    Freq Mode Depth
    Alert577 Dir Pk O f f
    86.9dB
    60%
    OK 
    						
    All 3M manuals Comments (0)

    Related Manuals for 3M DynatelTM 2250MMiD Cable Locating Quick Reference Guide