3M DynatelTM 1420 EMSiD Marker Locator Marker Locating Quick Reference Guide
Have a look at the manual 3M DynatelTM 1420 EMSiD Marker Locator Marker Locating Quick Reference Guide online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 307 3M manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
3M DynatelTM 1420 EMS-iD Marker Locator Marker Locating Quick Reference Guide [1] POWER: Turns unit off and on. [2] SPEAKER: Adjusts the volume of the receiver Marker Locate Markr 1 Markr 2 DepthPWR OFF Read 91% PWR 75dB 1420 EMS-iD Marker Locator OKMenu Gain Adjust Spkr/Xpand On/Off Dynatel TM Locate 10 7 4 6 5 2A 113 2 1 8 SK 12 9 [2A] SPEAKER ICON: Indicates the volume level of receiver. [3] CONTRAST: Adjust contrast of screen [4] GAIN: Adjust the sensitivity of the receiver [5] LOCATE/OK: Sets the receiver to cable locate mode. Acknowledges setup entries (OK) [6] MENU: Displays screens for configuration of the unit, i.e.: clock, depth units, etc. [7] BACKLIGHT: Toggles the backlight low, high, and off. [8] BATTERY ICON: Indicates battery level. [SK] SOFTKEYS: The function of each Softkey is shown above the key on the screen. [9] SOFT KEY COMMAND: Definitions for each of the four soft key functions. [10] SIGNAL STRENGTH: Digital reading of the signal the receiver is detecting. [11] BAR GRAPH: Graphical representation of the received signal. [12] Gain Level: Displays the relative gain level. Marker Locate Markr 1 ReadTEL Markr 2OFF Depth60% 39dB TEL Locating EMS Markers ss Power [1] ] oggle] to select desired utility. e no markers, raph [10] opens. 7. signal strength (dB) will be maximum when the receiver detects ote: Onl menu will be shown. (See 1420 manual: Enabling/Disabling Marker types). D Marker Depth er. eiver to the ground. ait…) If the rk pth of the marker, and its identification number. epth of Passive, Non-iD Marker eiver to the ground. The r iv marker (Calculating signal, please wait…) und. The e a om the ground level will display on the screen. eading iD Markers ta from the iD marker by pressing Read [SK]. . 1. Pre2. Press Locate [5] 3. Press Marker [SK4. Press Markr 1 [SK T5. Markr2 should be OFF. 6. In an area where there aradjust the Gain Down [4] until the bar gThe bar graph will close, the audio wi ll be steady, and thea marker of the specified utility. Ny the marker types enabled in the setup I Mem Select Press Locate when done Depth:12 in ID # : 000-000-0000 1. Target the mark2. Lower the tip of th e rec3. Press depth [SK] xamine the marker (Calculating signal, please w4. The receiver will e ma er is an iD marker: The receiver will display the de D Mem Select Press Locate when done Depth:12 in ID # : 000-000-0000 1. Target the marker. 2. Lower the tip of th e rec3. Press depth [SK] ece er will examine theThe screen will instruct the operator to raise the unit 6 inches from the gro4. Raise the unit 6 inches 5. Press Depth [SK] again.stim ted depth of the marker fr RThe operator can retrieve the daThe receiver tip should be lowered to the ground to reach maximum read depth Telecom Access Division 6801 River Place Blvd. Austin, TX 78726-9000 800-426-8688 http://www.3M.com/dynatel 78- 8135-5022-1 Rev. A